Nipros HDF-700 Manuale Utente Pagina 1

HDF-700/SVolume1, 1st edition Ver.1.0Operating Instructions取 扱 説 明 書Before operating the system, please read this manual thoroughly and remain it for

Names and Functions of Parts10HD View Finder HDF-700リアパネルRear panelTALLY 1 connector (BNC)TALLY 2 connector (BNC)Input a tally signal to light up the

Names and Functions of Parts11HD View Finder HDF-700リアパネルRear panelSDI(HD/SD) IN 1 connector (BNC)SDI(HD/SD) RET IN (SDI return signal input) connecto

Names and Functions of Parts12HD View Finder HDF-700リアパネルRear panelFanWorks when the POWER switch is turned on.電源スイッチを ON すると、ファンが回転します。DC IN connecto

Names and Functions of Parts13HD View Finder HDF-700左側面. 右側面 および 上面, 底面Left side, Right side, Upper & BottomScrew holes ( 2-w1/4, left, right) Use

Fixing 組み立て方法14HD View Finder HDF-700アームの取り付け方法VF Tilt Arm Stay FixingMake sure to disconnect the connectors before fixing up. 1Prepare the supplied

15FixingHD View Finder HDF-700アームの取り付け方法3Insert the VF Arm Stay into the gap between the combination washer and the screw, and tighten the armstay scr

16FixingHD View Finder HDF-700(for HDF-700/S only)(HDF-700/Sのみ)スイングアームへの取り付け方法 Mounting on Swing ArmMake sure to disconnect the connectors before fixin

17FixingHD View Finder HDF-700(for HDF-700/S only)Mount a camcorder on the tripod base on the swing arm.4スイングアーム上の三脚ベースへカメラを取り付けます。 Mounting on Swing

18ロケーションスタンドの脱着方法 Location Stand Removal and Fixing1Loosen/tighten four screws on the bottom to remove/fix.本体の底面の4本のネジで行います。FixingHD View Finder HDF-70

19FixingHD View Finder HDF-700(for HDF-700/S only)(HDF-700/Sのみ)フードの取り付け方法 Hood Mounting1Prepare the supplied Hood and four screws.フードと固定ネジ4本を用意します。Tig

WARNINGFor the customers in the U.S.A.This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Par

20(Fixing) Install the hood and tighten four screws to fix.2 本体にフードを取り付け、4本のネジで締め付けます。フード および マウントキット Removal and Fixing of the hood1(Removal) Loosen f

HDF-700 接続方法Connection 接続方法21HD View Finder HDF-700電源の接続方法Power Supply ConnectionMake sure to turn off the POWER switch of each unit before connectin

Connection22HD View Finder HDF-700HD/SD-SDIビデオ信号の接続HD/SD-SDI video signal connection1Connect the HD/SD-SDI output signal from a camera to the SDI (HD/

Connection23HD View Finder HDF-700HD/SDコンポーネントアナログ信号の接続HD/SD Analog Component Video Signal Connection1Connect the HD/SD analog component video output

Connection24HD View Finder HDF-700Monitor speaker2In case of using a headphone, connect the headphone jack to the headphone.ヘッドホンを使用する場合は、ヘッドホンジャックへ接続

25タリー信号の接続TALLY Signal Connection12Connect the tally output signal from a camera, a camera adaptor, switcher, etc. to the TALLY 1connector or TALLY 2

Connection26HD View Finder HDF-700ズームリモコンの接続Zoom Remote Controller (RETURN Controller) Connection1Connect the output signal from a zoom controller to

Adjustments and Settings 調整および設定27HD View Finder HDF-700ビデオ信号の設定・調整Video Signal Setting and Adjustment USER preset functions, etc. work when the vid

28HD View Finder HDF-700ビデオ信号の設定・調整Video Signal Setting and Adjustment3BRIGHT(brightness)/CONTRAST/PEAKING Adjustment(1)By pressing each knob select t

29HD View Finder HDF-700ビデオ信号の設定・調整Video Signal Setting and Adjustmentメニューの操作 - ユーザー設定 の方法Press the MENU button,and the menu list is displayed on the

各部名称と働きNames and Functions of Parts組み立て方法Fixing414HDF-700 目次Table of contents 目次HD View Finder HDF-700Front panel 4Rear panel 10Left side, Right sid

30ZEBRA buttonMARKER buttonOFF(no marker)16:916:9 with +4:34:3 with +all markers4:3/16:9CROSS HATCH (LARGE)OFFON←←←←←←←←←←USER setting←HD View Fin

31ユーザー設定User Function Setting6-3UTILITYOn the MENU, adjust and set the USER settingof the AUDIO, WAVEFORM and VECTORSCOPEin the USER position of the U

32ユーザー設定User Function SettingnoWAVEFORMWAVEFORM+VECTORSCOPEWAVEFORM+AUDIO 8CHWAVEFORM+VECTORSCOPE+AUDIO 8CH←←←←←←VECTORSCOPE (full screen)←WAVEFORM (f

33ユーザー設定User Function SettingWAVEFORMVECTORSCOPEAUDIO LEVEL METERHISTOGRAMAUDIO PEAK LOGUSER SettingWAVEFORM/HSG ［ON］AUDIO LEVEL METER ［ON］A

34ユーザー設定User Function SettingMenu of the WAVEFORM for the UTILITY settingsVECTORSCOPE ［ON］WAVEFORM/HSG ［ON］RETURNWAVEFORM ［ON］

35HD View Finder HDF-700オーディオの設定・調整AUDIO Signal Setting1By pressing MENU button on the front panel, access tothe MENU displayed on the screen.Access t

36HD View Finder HDF-700音声信号の設定Audio Signal Setting3By pressing the VOLUME / PUSH SELECT knob-button select the monitor audio signal by the monitor sp

37タリー信号の設定TALLY Signal Setting1Make sure that the front and rear TALLY indicators, RED and GREEN, light up properly when the tallysignal is input. And

38Adjustments and Settings補足AdditionHD Monitor HDF-700RETURNTIMECODE DISP ［OFF］TIMECODE TYPE ［LTC］TC TALLY ［OFF］COMPO

39Accessories 付属品HD View Finder HDF-700, HDF-700SK, HDF-700/SHDF-700 付属品HDF-700＜Contents＞HDF-700 main componentLocation standUniversal headVF tilt a

HDF-700 各部名称と働きNames and Functions of Parts04HD View Finder HDF-700フロントパネルFront panelRETURNMAINScreen (with Bezel and Protector)Front TALLY Indicator

40外形寸法図（単位：ミリ）Outside dimension (unit: mm)Outside View & Dimensions 外形寸法図HD View Finder HDF-700HDF-700 外形寸法図195147153195184.44650114.6153.4 (BEZ

41Specifications 仕様Features, design and specifications are subject to change without notice.デザイン, 仕様は、予告なく変更することがあります。Panel size7.0 inches diagonalPic

HDF-700 HDF-700SK HDF-700/S O p erating Ins t r u c t ionsTM

Names and Functions of Parts05HD View Finder HDF-700フロントパネルFront panelVOLUME / PUSH SELECT switchINPUT select switchZEBRA indication on/off switchMARKE

Names and Functions of Parts06HD View Finder HDF-700フロントパネルFront panelMENU button / ENTER knob-buttonMENU button : Pressing the MENU button displays t

Names and Functions of Parts07HD View Finder HDF-700フロントパネルFront panelBRIGHT level control volume and select switch / LED IndicatorCONTRAST control vo

Names and Functions of Parts08HD View Finder HDF-700Operating the Menus メニューの操作PressRotateMenu Displayメニューの表示Press the MENU button.VECTORSC

Names and Functions of Parts09HD View Finder HDF-700VECTORSCOPE ［ON］ZEBRA ［OFF］SDI STATUS ［OFF］SETUPRETURNTIMECODE DISP